Fix serial number retrieval from EEPROM

[riso-kagaku-clone.git] / usbconfig.h

diff --git a/usbconfig.h b/usbconfig.h
index 56a980e6e742e390f569dd71007f946c88f1f97c..ffc4bc722e8cd3638952e865d8a9965eb6ef1509 100644 (file)
--- a/usbconfig.h
+++ b/usbconfig.h
@@ -10,6 +10,8 @@
 #ifndef __usbconfig_h_included__
 #define __usbconfig_h_included__
 
+#include "osccal.h"
+
 /*
 General Description:
 This file is an example configuration (with inline documentation) for the USB
@@ -29,11 +31,11 @@ section at the end of this file).
 /* This is the port where the USB bus is connected. When you configure it to
  * "B", the registers PORTB, PINB and DDRB will be used.
  */
-#define USB_CFG_DMINUS_BIT      1
+#define USB_CFG_DMINUS_BIT      3
 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
  * This may be any bit in the port.
  */
-#define USB_CFG_DPLUS_BIT       2
+#define USB_CFG_DPLUS_BIT       4
 /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
  * This may be any bit in the port. Please note that D+ must also be connected
  * to interrupt pin INT0! [You can also use other interrupts, see section
@@ -162,11 +164,7 @@ section at the end of this file).
  * proceed, do a return after doing your things. One possible application
  * (besides debugging) is to flash a status LED on each packet.
  */
-#ifndef __ASSEMBLER__
-#include <avr/interrupt.h>  // for sei()
-extern void calibrateOscillator(void);
-#endif
-#define USB_RESET_HOOK(resetStarts)  if(!resetStarts){cli(); calibrateOscillator(); sei();}
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
 /* This macro is a hook if you need to know when an USB RESET occurs. It has
  * one parameter which distinguishes between the start of RESET state and its
  * end.
@@ -207,7 +205,7 @@ extern void calibrateOscillator(void);
  * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
  * for each control- and out-endpoint to check for duplicate packets.
  */
-#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   1
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
 /* define this macro to 1 if you want the function usbMeasureFrameLength()
  * compiled in. This function can be used to calibrate the AVR's RC oscillator.
  */
@@ -378,13 +376,13 @@ extern void calibrateOscillator(void);
  * which is not fully supported (such as IAR C) or if you use a differnt
  * interrupt than INT0, you may have to define some of these.
  */
-/* #define USB_INTR_CFG            MCUCR */
-/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
-/* #define USB_INTR_CFG_CLR        0 */
-/* #define USB_INTR_ENABLE         GIMSK */
-/* #define USB_INTR_ENABLE_BIT     INT0 */
-/* #define USB_INTR_PENDING        GIFR */
-/* #define USB_INTR_PENDING_BIT    INTF0 */
-/* #define USB_INTR_VECTOR         INT0_vect */
+#define USB_INTR_CFG            PCMSK
+#define USB_INTR_CFG_SET        (1 << USB_CFG_DPLUS_BIT)
+#define USB_INTR_CFG_CLR        0
+#define USB_INTR_ENABLE         GIMSK
+#define USB_INTR_ENABLE_BIT     PCIE
+#define USB_INTR_PENDING        GIFR
+#define USB_INTR_PENDING_BIT    PCIF
+#define USB_INTR_VECTOR         PCINT0_vect
 
 #endif /* __usbconfig_h_included__ */