Linux version 2.6.8-rc3 (noodles@super) (gcc version 3.3.4 (Debian 1:3.3.4-3)) #1 Wed Aug 4 18:33:28 BST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e5c00 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000bfe0000 (usable) BIOS-e820: 000000000bfe0000 - 000000000bff2c00 (ACPI data) BIOS-e820: 000000000bff2c00 - 000000000c000000 (ACPI NVS) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 191MB LOWMEM available. On node 0 totalpages: 49120 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 45024 pages, LIFO batch:10 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 COMPAQ ) @ 0x000f6950 ACPI: RSDT (v001 COMPAQ RSDTBL 0x06040000 CPQ 0x00000000) @ 0x0bfec745 ACPI: FADT (v001 COMPAQ EVO N200 0x06040000 PTL 0x000f4240) @ 0x0bff2b54 ACPI: BOOT (v001 COMPAQ EVO 0x06040000 PTL 0x00000001) @ 0x0bff2bd8 ACPI: DSDT (v001 PTL BX-TJ 0x06040000 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x8008 Built 1 zonelists Kernel command line: root=/dev/hda1 ro resume=/dev/hda2 Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 PID hash table entries: 1024 (order 10: 8192 bytes) Detected 696.714 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 191324k/196480k available (1657k kernel code, 4504k reserved, 756k data, 140k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 1384.44 BogoMIPS Security Scaffold v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel(R) Pentium(R) III Mobile CPU 700MHz stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 696.0440 MHz. ..... host bus clock speed is 99.0491 MHz. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd9de, last bus=0 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: IRQ9 SCI: Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 14 15) ACPI: Device [FDDA] status [00000008]: functional but not present; setting present ACPI: Embedded Controller [EC0] (gpe 26) ACPI: Power Resource [PIDE] (off) Linux Kernel Card Services options: [pci] [cardbus] [pm] PCI: Using ACPI for IRQ routing ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:00.1[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9 ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI interrupt 0000:00:0e.1[A] -> GSI 9 (level, low) -> IRQ 9 NET: Registered protocol family 23 vesafb: probe of vesafb0 failed with error -6 Simple Boot Flag value 0x0 read from CMOS RAM was invalid Simple Boot Flag at 0x37 set to 0x80 Initializing Cryptographic API ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) ACPI: Battery Slot [BAT2] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SBTN] ACPI: Lid Switch [LID] ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states) ACPI: Thermal Zone [THRM] (44 C) Real Time Clock Driver v1.12 e100: Intel(R) PRO/100 Network Driver, 3.0.18 e100: Copyright(c) 1999-2004 Intel Corporation ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 9 (level, low) -> IRQ 9 e100: eth0: e100_probe: addr 0xfc020000, irq 9, MAC addr 00:D0:59:82:55:A5 nsc-ircc, Found chip at base=0x398 nsc-ircc, driver loaded (Dag Brattli) IrDA: Registered device irda0 nsc-ircc, Found dongle: Sharp RY5HD01 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 0 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1040-0x1047, BIOS settings: hda:DMA, hdb:pio hda: IC25N020ATDA04-0, ATA DISK drive hdb: CD-224E, ATAPI CD/DVD-ROM drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 128KiB hda: 39070080 sectors (20003 MB) w/1806KiB Cache, CHS=38760/16/63, UDMA(33) hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 > PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:0a.0 [0e11:b103] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:0a.0, mfunc 0x01201212, devctl 0x64 Yenta: ISA IRQ mask 0x00f0, PCI irq 11 Socket status: 30000006 mice: PS/2 mouse device common for all mice input: PC Speaker serio: i8042 AUX port at 0x60,0x64 irq 12 Synaptics Touchpad, model: 1 Firmware: 5.8 Sensor: 17 new absolute packet format Touchpad has extended capability bits -> multifinger detection -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio1 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 8Kbytes TCP: Hash tables configured (established 16384 bind 32768) NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 cpufreq: CPU0 - ACPI performance management activated. cpufreq: *P0: 700 MHz, 15000 mW, 500 uS cpufreq: P1: 300 MHz, 9500 mW, 500 uS Resume Machine: resuming from /dev/hda2 Resuming from device unknown-block(3,2) Resume Machine: This is normal swap space ACPI: (supports S0 S3 S4 S5) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 140k freed Adding 393112k swap on /dev/hda2. Priority:-1 extents:1 EXT3 FS on hda1, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda8, internal journal EXT3-fs: mounted filesystem with ordered data mode. ACPI: PCI interrupt 0000:00:00.1[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:00.1 to 64 intel8x0_measure_ac97_clock: measured 49703 usecs intel8x0: clocking to 48000 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 9 (level, low) -> IRQ 9 uhci_hcd 0000:00:07.2: Intel Corp. 82440MX USB Universal Host Controller uhci_hcd 0000:00:07.2: irq 9, io base 00001060 uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usb 1-2: new full speed USB device using address 2 hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected usb 1-2.4: new full speed USB device using address 3 uss720: probe: vendor id 0x1293, device id 0x2 uss720: set inteface result 0 uss720: (C) 1999 by Thomas Sailer, uss720: reg: da 0c 23 00 00 00 01 uss720: epaddr 131 interval 1 bad: scheduling while atomic! [] schedule+0x499/0x4a0 [] uhci_submit_control+0x22c/0x270 [uhci_hcd] [] wait_for_completion+0x78/0xd0 [] default_wake_function+0x0/0x10 [] hcd_submit_urb+0x111/0x1a0 [usbcore] [] default_wake_function+0x0/0x10 [] usb_start_wait_urb+0x81/0xc0 [usbcore] [] register_proc_table+0xaf/0x110 [] timeout_kill+0x0/0x80 [usbcore] [] usb_internal_control_msg+0x62/0x80 [usbcore] [] usb_control_msg+0x8f/0xb0 [usbcore] [] set_1284_register+0x6f/0xb0 [uss720] [] parport_uss720_restore_state+0x1b/0x50 [uss720] [] parport_claim+0x10e/0x210 [parport] [] parport_open+0x98/0xf0 [parport] [] parport_claim_or_block+0xf/0x60 [parport] [] parport_device_id+0x42/0x1a0 [parport] [] parport_daisy_init+0x83/0x1d0 [parport] [] call_console_drivers+0x7f/0x100 [] parport_announce_port+0xf/0xd0 [parport] [] uss720_probe+0x16d/0x1a0 [uss720] [] usb_probe_interface+0x4c/0x60 [usbcore] [] bus_match+0x32/0x60 [] driver_attach+0x59/0x90 [] kobject_register+0x22/0x60 [] bus_add_driver+0x8c/0xb0 [] driver_register+0x28/0x30 [] usb_register+0x3a/0xa0 [usbcore] [] uss720_init+0x11/0x36 [uss720] [] sys_init_module+0xe8/0x1f0 [] syscall_call+0x7/0xb bad: scheduling while atomic! [] schedule+0x499/0x4a0 [] uhci_submit_control+0x22c/0x270 [uhci_hcd] [] wait_for_completion+0x78/0xd0 [] default_wake_function+0x0/0x10 [] hcd_submit_urb+0x111/0x1a0 [usbcore] [] default_wake_function+0x0/0x10 [] usb_start_wait_urb+0x81/0xc0 [usbcore] [] register_proc_table+0xaf/0x110 [] timeout_kill+0x0/0x80 [usbcore] [] usb_internal_control_msg+0x62/0x80 [usbcore] [] usb_control_msg+0x8f/0xb0 [usbcore] [] set_1284_register+0x6f/0xb0 [uss720] [] parport_uss720_restore_state+0x2b/0x50 [uss720] [] parport_claim+0x10e/0x210 [parport] [] parport_open+0x98/0xf0 [parport] [] parport_claim_or_block+0xf/0x60 [parport] [] parport_device_id+0x42/0x1a0 [parport] [] parport_daisy_init+0x83/0x1d0 [parport] [] call_console_drivers+0x7f/0x100 [] parport_announce_port+0xf/0xd0 [parport] [] uss720_probe+0x16d/0x1a0 [uss720] [] usb_probe_interface+0x4c/0x60 [usbcore] [] bus_match+0x32/0x60 [] driver_attach+0x59/0x90 [] kobject_register+0x22/0x60 [] bus_add_driver+0x8c/0xb0 [] driver_register+0x28/0x30 [] usb_register+0x3a/0xa0 [usbcore] [] uss720_init+0x11/0x36 [uss720] [] sys_init_module+0xe8/0x1f0 [] syscall_call+0x7/0xb bad: scheduling while atomic! [] schedule+0x499/0x4a0 [] uhci_submit_control+0x22c/0x270 [uhci_hcd] [] wait_for_completion+0x78/0xd0 [] default_wake_function+0x0/0x10 [] hcd_submit_urb+0x111/0x1a0 [usbcore] [] default_wake_function+0x0/0x10 [] usb_start_wait_urb+0x81/0xc0 [usbcore] [] kref_put+0x15/0x20 [] usb_start_wait_urb+0xb1/0xc0 [usbcore] [] register_proc_table+0xaf/0x110 [] timeout_kill+0x0/0x80 [usbcore] [] timeout_kill+0x0/0x80 [usbcore] [] usb_internal_control_msg+0x62/0x80 [usbcore] [] usb_control_msg+0x8f/0xb0 [usbcore] [] get_1284_register+0x72/0x120 [uss720] [] parport_claim+0x10e/0x210 [parport] [] parport_open+0x98/0xf0 [parport] [] parport_claim_or_block+0xf/0x60 [parport] [] parport_device_id+0x42/0x1a0 [parport] [] parport_daisy_init+0x83/0x1d0 [parport] [] call_console_drivers+0x7f/0x100 [] parport_announce_port+0xf/0xd0 [parport] [] uss720_probe+0x16d/0x1a0 [uss720] [] usb_probe_interface+0x4c/0x60 [usbcore] [] bus_match+0x32/0x60 [] driver_attach+0x59/0x90 [] kobject_register+0x22/0x60 [] bus_add_driver+0x8c/0xb0 [] driver_register+0x28/0x30 [] usb_register+0x3a/0xa0 [usbcore] [] uss720_init+0x11/0x36 [uss720] [] sys_init_module+0xe8/0x1f0 [] syscall_call+0x7/0xb Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A PCI: Enabling device 0000:00:0e.1 (0000 -> 0003) ACPI: PCI interrupt 0000:00:0e.1[A] -> GSI 9 (level, low) -> IRQ 9 parport0: Printer, EPSON Stylus COLOR 480 usbcore: registered new driver uss720 drivers/usb/misc/uss720.c: v0.5:USB Parport Cable driver for Cables using the Lucent Technologies USS720 Chip